The power window for drivers side will not close completely.It will stop 2 to 3 inch before.The power window operates fine.It goes up/down properly without any blockage,but will not close full.
Its the cause of weak motor.
The problem is typically Internal to the Window Motor & the Window Motor needs to be replaced
Follow the test procedure to confirm the issue with motor:------
Testing of the "2" wires at the Window Motor should be made for "Reverse" Ground - & Voltage +, prior to replacing
Use of a VOM is needed to test
The way it works:
Ignition On
With Power window Switch held in Up position
One wire will have 12 Volts +
One wire will have Ground -
And With Power window Switch held in Down position
The wire that had 12 Volts + is now Ground -
The wire that was Ground - is now 12 Volts +
If Voltage or Ground checks good at motor, replace motor.
If Voltage or Ground does not check good:
Check Switch Voltage & Ground.
Check for broken wires at Door / Kick Panel Boot.
There will be loose or short wire noticed.
This details will help.
Thanks.
How to replace window motor and regulator on 2007 Ford Taurus?
Mercedes Power windows and Regulator Removal?
http://howtobyme.blogspot.in/2012/03/mercedes-power-windows-and-regulator.html
Power windows not working after car wash?
http://howtobyme.blogspot.com/2011/11/power-windows-not-working-after-car.html
1996
http://whatisbyme.blogspot.in/2012/05/1996-toyota-camry-power-window-fuse.html
1992
http://whatisbyme.blogspot.in/2012/04/1992-toyota-camry-master-switch-not.html
2002
http://technoanswers.blogspot.in/2012/04/2002-toyota-sienna-wipers-and-passenger.html
Its the cause of weak motor.
The problem is typically Internal to the Window Motor & the Window Motor needs to be replaced
Follow the test procedure to confirm the issue with motor:------
Testing of the "2" wires at the Window Motor should be made for "Reverse" Ground - & Voltage +, prior to replacing
Use of a VOM is needed to test
The way it works:
Ignition On
With Power window Switch held in Up position
One wire will have 12 Volts +
One wire will have Ground -
And With Power window Switch held in Down position
The wire that had 12 Volts + is now Ground -
The wire that was Ground - is now 12 Volts +
If Voltage or Ground checks good at motor, replace motor.
If Voltage or Ground does not check good:
Check Switch Voltage & Ground.
Check for broken wires at Door / Kick Panel Boot.
There will be loose or short wire noticed.
This details will help.
Thanks.
Users Who Viewed This Problem Also Viewed:
How to replace window motor and regulator on 2007 Ford Taurus?
Ford Taurus Window System Circuit diagram?
http://repairhelpcenter.blogspot.in/2012/03/how-to-replace-window-motor-and.htmlMercedes Power windows and Regulator Removal?
http://howtobyme.blogspot.in/2012/03/mercedes-power-windows-and-regulator.htmlPower windows not working after car wash?
http://howtobyme.blogspot.com/2011/11/power-windows-not-working-after-car.html1996 Toyota Camry: Power Window Fuse Blows Repeatedly?
http://whatisbyme.blogspot.in/2012/05/1996-toyota-camry-power-window-fuse.html1992 Toyota Camry: Master Switch Not Operating Power Window?
http://whatisbyme.blogspot.in/2012/04/1992-toyota-camry-master-switch-not.html2002 Toyota Sienna: Wipers and Passenger side Power window stopped working?
http://technoanswers.blogspot.in/2012/04/2002-toyota-sienna-wipers-and-passenger.htmlFor All types of Car models and brands help
Go to Newly Launched
FREE Car repair guide?
http://technoanswers.blogspot.in/2012/03/car-repair-guide.html
Go to Newly Launched
FREE Car repair guide?
http://technoanswers.blogspot.in/2012/03/car-repair-guide.html
&
Complete Car repair Help FREE?
http://repairhelpcenter.blogspot.in/2012/03/complete-car-repair-help.htmlComplete Car repair Help FREE?
No comments:
Post a Comment