BannerFans.com

Tuesday, August 2, 2011

clutch replacement on Moto Guzzi 850 T3 California?

This procedure relates to:----

Moto GuzziV7 Sport, 750 S, 750 S3, 850 T, 850-T3, 850-T3 California, V1000 I-Convert, V1000 G5, 1000 SP, Le Mans, Le Mans II, Le Mans CX100


--------------

Converter cover disassembly

The transmission is really two separate units that are bolted together and interface with one another through dry clutch plates. The “converter cover” is the front unit, and it is bolted to the rear “gear box” unit. I began disassembly by removing the converter cover from the 2 speed gear box.

Start by removing the bronze bushing from the shaft so…
Start by removing the bronze bushing from the shaft so it won't fall out later.

Direct link to image

It just slides out. During reassembly the only thing that…
It just slides out. During reassembly the only thing that matters is that the notches face the front.

Direct link to image

Remove the 6 bolts that secure that converter cover to…
Remove the 6 bolts that secure that converter cover to the 2 speed gearbox. The converter cover will then separate from the 2 speed gearbox.

Direct link to image

This is the rear side of the converter cover. The…
This is the rear side of the converter cover. The splined piece is the clutch input hub that interfaces with the clutch plates.

Direct link to image

In order to remove the clutch input hub assembly from…
In order to remove the clutch input hub assembly from the convert cover, you need to remove 5 bolts. Rotate the clutch input hub until the bolts are visible through the access holes.

Direct link to image

Remove each of the 5 bolts and withdraw the assembly.…
Remove each of the 5 bolts and withdraw the assembly. The complete clutch input hub assembly should slide right out of the converter cover.

Direct link to image

Here is the seal (90404563) and several of the passages…
Here is the seal (MG# 90404563) and several of the passages that must be aligned with the corresponding passages in the clutch input hub assembly during reassembly.

Direct link to image

Drive the seal out  …
Drive the seal out (MG# 90404563).

Direct link to image

Here is how the seal (90404563) must be positioned during…
Here is how the seal (MG# 90404563) must be positioned during assembly.

Direct link to image

A view of the rear side of the converter …
A view of the rear side of the converter cover.

Direct link to image

Note the use of multiple aluminum crush washers to prevent…
Note the use of multiple aluminum crush washers to prevent the acorn nuts from bottoming out before making a tight seal.

Direct link to image

A closer view of the fittings for the oil lines.…
A closer view of the fittings for the oil lines. Notice the bottom one is a smaller diameter than the top one. I removed both of these fittings. That about covers the removal and disassembly of the converter cover.

Direct link to image

Clutch input hub disassembly

With the clutch input hub removed from the converter cover, we can disassemble it.

Now we turn our attention to disassembling the clutch input…
Now we turn our attention to disassembling the clutch input hub. Start by removing this o-ring (MG# 90706600).

Direct link to image

Note the holes that must align with the passageways in…
Note the holes that must align with the passageways in the converter cover during assembly. You can see that I've already started to separate the two halves that were held together by the 5 bolts.

Direct link to image

Here is another hole that must be aligned with the…
Here is another hole that must be aligned with the passageways in the converter cover during assembly.

Direct link to image

Completely separate the two halves that were held together by…
Completely separate the two halves that were held together by the 5 bolts. I was able to accomplish this using small screwdrivers and careful prying.

Direct link to image

Remove the o-ring (90706473) from the front  …
Remove the o-ring (MG# 90706473) from the front half.

Direct link to image

This hole in the front half is supposed to be…
This hole in the front half is supposed to be plugged (the other hole on the opposite side should not be plugged).

Direct link to image

Remove the o-ring (90706158) from the  …
Remove the o-ring (MG# 90706158) from the shaft.

Direct link to image

Remove the snap ring (90271020) from the shaft. This snap…
Remove the snap ring (MG# 90271020) from the shaft. This snap ring keeps the bearing in place.

Direct link to image

Pull the bearing (92201220) from the shaft. If I remember…
Pull the bearing (MG# 92201220) from the shaft. If I remember correctly, I needed to use a press (or puller) to pull up on the bottom half (with the 5 bolt holes). This is necessary because the bearing sits inside of it and you can't get a grip on the bottom of the bearing. Just be careful not to bend the bottom half when you use your press (or puller).

Direct link to image

Remove the bearing  …
Remove the bearing (MG# 92201220).

Direct link to image

Remove the seal (90402535), note the direction that it must…
Remove the seal (MG# 90402535), note the direction that it must be installed. I'm certain I removed the seal after I'd removed the plate. I just took the picture here to be clear about assembly order, etc.

Direct link to image

Remove the bottom  …
Remove the bottom plate.

Direct link to image

Clutch basket disassembly

The clutch basket needs to be removed before we can disassemble the gear box.

With the converter cover removed and the clutch input hub…
With the converter cover removed and the clutch input hub disassembled, I turned my attention to the 2 speed gearbox. Here is the stack of clutch plates installed.

Direct link to image

Here is the snap ring that must be removed. In…
Here is the snap ring that must be removed. In order to do that, we must first take the pressure off of the clutch and intermediate plates.

Direct link to image

I used the clutch throw out bearing adjustment nut at…
I used the clutch throw out bearing adjustment nut at the rear of the transmission to take the pressure off of the clutch and intermediate plates.

Direct link to image

First, remove the smaller jam nut from the back of…
First, remove the smaller jam nut from the back of the transmission.

Direct link to image

I also removed the adjustment nut and the lever so…
I also removed the adjustment nut and the lever so I could clean and lubricate the threads. Also, I wanted to remove the rubber boot from the lever so it would be easier to tighten the adjustment nut.

Direct link to image

I put the lever back on with the adjustment nut.…
I put the lever back on with the adjustment nut. I then tightened the adjustment nut to compress the clutch springs and take the pressure off of the clutch plates. Go slow here. You may need to completely remove the adjustment nut, then clean and lubricate the threads so that you don't destroy the threads in the process.

Direct link to image

With the large snap ring removed, you can withdraw all…
With the large snap ring removed, you can withdraw all of the clutch and intermediate plates.

Direct link to image

Here is the stack of clutch and intermediate plates. I…
Here is the stack of clutch and intermediate plates. I kept them in the original order throughout cleaning and reassembly. It shouldn't matter, but when reusing used parts I like to error on the side of same-ness.

Direct link to image

Remove the adjustment  …
Remove the adjustment nut.

Direct link to image

And withdraw the clutch throw out bearing pull rod from…
And withdraw the clutch throw out bearing pull rod from the front of the gearbox.

Direct link to image

Another view of the pull rod being  …
Another view of the pull rod being removed.

Direct link to image

The throw out bearing (92204217) came out  …
The throw out bearing (MG# 92204217) came out easily.

Direct link to image

Another view of the throw out bearing (92204217) being …
Another view of the throw out bearing (MG# 92204217) being removed.

Direct link to image

This is the special insert that fits inside the throw…
This is the special insert that fits inside the throw out bearing (MG# 92204217).

Direct link to image

Remove the pressure plate. Note the 6 springs and the…
Remove the pressure plate. Note the 6 springs and the thin washers. The washers fit within the recesses of the pressure plate, not in the basket.

Direct link to image

Another view of the pressure plate with thin washers and…
Another view of the pressure plate with thin washers and springs.

Direct link to image

The lip of the nut will have been peened into…
The lip of the nut will have been peened into the slot in the shaft. Pry the peened portion away from the shaft.

Direct link to image

And remove the  …
And remove the nut.

Direct link to image

Remove the basket. Mine came off pretty easily without much…
Remove the basket. Mine came off pretty easily without much fuss.

Direct link to image

A seal runs on this surface, be sure to clean…
A seal runs on this surface, be sure to clean and dress it properly.

Direct link to image

With the clutch basket removed, you can now see the…
With the clutch basket removed, you can now see the front of the gearbox and the seal.

Direct link to image

Note the seal  …
Note the seal (MG# 90402838).

Direct link to image

And the o-ring (not shown in the parts book). Before…
And the o-ring (not shown in the parts book). Before we remove the seal or o-ring, however, lets disassemble the gear box.

Direct link to image

Gear box disassembly

With the clutch basket removed from the gear box, we can now disassemble the gear box.

A view of the rear of the  …
A view of the rear of the transmission.

Direct link to image

Here is the shift arm and how it was originally…
Here is the shift arm and how it was originally positioned.

Direct link to image

Well start disassembling the gear box by removing the speedometer…
We'll start disassembling the gear box by removing the speedometer drive gear.

Direct link to image

Remove the gear  …
Remove the gear drive.

Direct link to image

And use a small magnet to withdraw the hardened steel…
And use a small magnet to withdraw the hardened steel washer down inside that hole.

Direct link to image

Set the transmission up on end. Remove the spring loaded…
Set the transmission up on end. Remove the spring loaded plug that holds gear selector pawl in place.

Direct link to image

Remove the crush  …
Remove the crush washer.

Direct link to image

Withdraw the spring and selector  …
Withdraw the spring and selector pawl.

Direct link to image

Remove the drain plug along with its crush  …
Remove the drain plug along with its crush washer.

Direct link to image

Remove all of the bolts that secure the cover to…
Remove all of the bolts that secure the cover to the case.

Direct link to image

Here is the snap ring on the output  …
Here is the snap ring on the output shaft.

Direct link to image

Remove the snap ring (this could also be removed after…
Remove the snap ring (this could also be removed after the cover is removed).

Direct link to image

Remove the cover from the  …
Remove the cover from the case.

Direct link to image

The inside of the  …
The inside of the cover.

Direct link to image

The gears inside the  …
The gears inside the transmission.

Direct link to image

A closer  …
A closer view.

Direct link to image

Remove the thrust/shimming  …
Remove the thrust/shimming washers.

Direct link to image

There were two placed to the rear of the …
There were two placed to the rear of the bearing.

Direct link to image

Then remove the thrust  …
Then remove the thrust bearing.

Direct link to image

There was a single thrust/shimming washer in front of the…
There was a single thrust/shimming washer in front of the bearing.

Direct link to image

The shift fork assembly is secured to the splined shaft…
The shift fork assembly is secured to the splined shaft via a pinch bolt.

Direct link to image

Note the alignment of the external shift arm with the…
Note the alignment of the external shift arm with the nub on the shift fork assembly.

Direct link to image

Remove the pinch  …
Remove the pinch bolt.

Direct link to image

Withdraw the external shift arm/splined  …
Withdraw the external shift arm/splined shaft.

Direct link to image

Note the o-ring  …
Note the o-ring (MG# 90706108).

Direct link to image

Remove the input  …
Remove the input shaft.

Direct link to image

The input shaft and the o-ring that seals the input…
The input shaft and the o-ring that seals the input shaft and the inner race of the bearing. Note that the o-ring is fit outside of the gearbox, in between the clutch basket and the bearing.

Direct link to image

The bearing retainer is secured by three  …
The bearing retainer is secured by three bolts.

Direct link to image

Remove the three bolts and the bearing  …
Remove the three bolts and the bearing retainer.

Direct link to image

This is the puller arrangement I devised to get the…
This is the puller arrangement I devised to get the rear bearing and the spacer that the seal runs on off of the output shaft. I chose to pull them off as a unit because (a) the spacer that the seal runs on was stuck in place and (b) I did not want to risk damaging the sealing surface of the spacer that the seal runs on. The clamp was very useful to keep the fingers of the puller lodged under the bearing.

Direct link to image

Another view of the puller  …
Another view of the puller arrangement.

Direct link to image

And a close up view of the puller  …
And a close up view of the puller arrangement.

Direct link to image

Here is the spacer that the seal runs on. I…
Here is the spacer that the seal runs on. I was able to clean this up nicely.

Direct link to image

The o-ring (90706222) remained on the shaft when I pulled…
The o-ring (MG# 90706222) remained on the shaft when I pulled the bearing off.

Direct link to image

Here is where the o-ring (90706222) fits: within the front…
Here is where the o-ring (MG# 90706222) fits: within the front recess of the spacer that the seal runs on.

Direct link to image

Remove the shimming  …
Remove the shimming washer.

Direct link to image

Remove the normal speed  …
Remove the normal speed gear.

Direct link to image

Now the main shaft is easily removed from the front…
Now the main shaft is easily removed from the front bearing.

Direct link to image

Remove the shift sleeve. Note which side face rearward and…
Remove the shift sleeve. Note which side face rearward and which side faced frontward. The shift sleeve can be reversed to double the life of the engagement dogs.

Direct link to image

Note how one side of the engagement dogs is rounded.…
Note how one side of the engagement dogs is rounded. This is what happens when convert transmissions are shifted at speed. They should always be shifted when the machine is not in motion.

Direct link to image

A view of the other side of the shift …
A view of the other side of the shift sleeve.

Direct link to image

The output shaft was pretty well stuck in the front…
The output shaft was pretty well stuck in the front bearing and there is no good way to “pry” it out. So, I welded up a small adapter for my slide hammer so that I could pull the shaft out. The end of the shaft is already threaded for 8 mm × 1.25 mm threads, so all I needed to do was weld a bolt onto the end of an adapter. This worked a treat!

Direct link to image

Another view of the puller I used to withdraw the…
Another view of the puller I used to withdraw the output shaft from the bearing.

Direct link to image

Another view of the puller I used to withdraw the…
Another view of the puller I used to withdraw the output shaft from the bearing.

Direct link to image

Another view of the puller I used to withdraw the…
Another view of the puller I used to withdraw the output shaft from the bearing.

Direct link to image

The output shaft  …
The output shaft (layshaft).

Direct link to image

The low speed gear remained in the  …
The low speed gear remained in the box.

Direct link to image

Here is the low speed gear back in place on…
Here is the low speed gear back in place on the output shaft (layshaft). Note the shimming washer is still on top of the bearing.

Direct link to image

The shimming washer is now in place on the output…
The shimming washer is now in place on the output shaft (layshaft).

Direct link to image

Use a seal puller to remove the seal from the…
Use a seal puller to remove the seal from the case. Be careful not to gouge the case or else you'll have trouble getting the next seal installed and you may have trouble with it sealing properly.

Direct link to image

Here is the removed seal. The lip of the seal…
Here is the removed seal. The lip of the seal presses against the clutch basket.

Direct link to image

Press out the front bearing for the input  …
Press out the front bearing for the input shaft.

Direct link to image

Here is the blind hole bearing puller I used to…
Here is the blind hole bearing puller I used to remove the bearings from the case.

Direct link to image

Another view of the blind hole bearing  …
Another view of the blind hole bearing puller.

Direct link to image

Another view of the blind hole bearing  …
Another view of the blind hole bearing puller.

Direct link to image

Another view of the blind hole bearing  …
Another view of the blind hole bearing puller.

Direct link to image

Another view of the blind hole bearing  …
Another view of the blind hole bearing puller.

Direct link to image

Another view of the blind hole bearing  …
Another view of the blind hole bearing puller.

Direct link to image

Another view of the blind hole bearing  …
Another view of the blind hole bearing puller.

Direct link to image

Removing the bolt from the case. I think the purpose…
Removing the bolt from the case. I think the purpose of this bolt was to prevent the shift shaft from rotating too far. I can't recall for sure now, though.

Direct link to image

Here is the bolt  …
Here is the bolt removed.

Direct link to image

Use a seal puller to remove the output shaft (layshaft)…
Use a seal puller to remove the output shaft (layshaft) seal from the rear cover.

Direct link to image

Here is the removed  …
Here is the removed seal.

Direct link to image

Use a small driver to drive out the seal from…
Use a small driver to drive out the seal from the rear cover. The bearing will come with it. Take care so as to not destroy the bearing (I do not use a blind hole bearing puller on these bearings unless I have to). Use the largest size drive you can fit.

Direct link to image

Here is the seal and bearing  …
Here is the seal and bearing removed.

Direct link to image

Here is the vent. I never did remove this from…
Here is the vent. I never did remove this from the case. Just cleaned it thoroughly in place along with the rest of the case.

Direct link to image



Output (layshaft) seal

The physical dimensions of this single lip seal (MG# 90403547) are as follows:

  • Inside diameter: 35 mm
  • Outside diameter: 47 mm
  • Width: 7 mm

Input (clutch) shaft seal - rear

The physical dimensions of this single lip seal (MG# 90401630) are as follows:

  • Inside diameter: 16 mm
  • Outside diameter: 30 mm
  • Width: 7/6.5 mm

Input (clutch) shaft seal - front (small, fits into transmission case)

The physical dimensions of this single lip seal (MG# 90402838) are as follows:

  • Inside diameter: 28 mm
  • Outside diameter: 38 mm
  • Width: 7 mm

Input (clutch) shaft seal - front (large, fits into clutch case)

The physical dimensions of this single lip seal (MG# 90404563) are as follows:

  • Inside diameter: 45 mm
  • Outside diameter: 60 mm
  • Width: 7 mm

Clutch area seal

The physical dimensions of this single lip seal (MG# 90402535) are as follows:

  • Inside diameter: 25 mm
  • Outside diameter: 35 mm
  • Width: 7 mm

Clutch assembly bearing

The physical dimensions of the bearing used in the clutch assembly (MG# 92201220) is as follows:

  • Inside diameter: 20 mm
  • Outside diameter: 47 mm
  • Width: 14 mm

IF you require work shop manual for your Moto Guzzi 850 T3, click the link below:---



1 comment:

  1. That's a good guide you put up. You'll have to excuse me for not typing more but I'm using an iPad and I absolutely hate it. My '78 T3 needs clutch work as well and this guide will help me do it. I've just bought the clutch parts and will start disassembly in the coming weeks.

    ReplyDelete