BannerFans.com

Sunday, July 8, 2012

Where is A/C Pressure Switch Located on Mercedes?

2000 Mercedes Benz ML320 Low pressure Switch Location.


For Location of  Low pressure switch just follow the refrigerant line from A/c compressor to the condenser.

How to replace the Low Pressure Switch?

Its very simple the old one screws out and new one screws IN.

pressure switch depresses a valve core when it screws on. It's probably safer to remove the refrigerant but if you look at your new switch and it has a pointed center to depress the core you should be able to just unscrew the old one and screw on the new one.
On some cases the refrigerant has to be drained out from the system then the switch can be replaced.


For refrigerant pressure sensor/Switch location see the diagram Image shown below :----
Ac pressure switch

This details and diagram will help.
Thanks.


Users Who Viewed This Problem Also Viewed:



2002 Buick Rendezvous: Add Refrigerant In A/C System?

http://whatisbyme.blogspot.in/2012/06/2002-buick-rendezvous-add-refrigerant.html

Where Is AC Low Pressure Port Located On Ford LCF 2006?

http://whoisbyme.blogspot.in/2012/07/where-is-ac-low-pressure-port-located.html


How to Remove A/C belt?

http://schematicsdiagram.blogspot.in/2012/06/1998-chrysler-concorde-how-to-remove-ac.html


A/C Blows Warm?

http://whoisbyme.blogspot.in/2012/06/2005-chrysler-pt-cruiser-ac-blows-warm.html


A/C blows Cold From Defrost Vent Only?

http://whoisbyme.blogspot.in/2012/06/2009-mercury-grand-marquis-ac-blows.html



Where Is AC Low Pressure Port Located On Ford LCF 2006?

When the AC refrigerant /Freon Level gets low the A/C system needs to be charged with refrigerant.

The A/C recharging has to be done from Low pressure port.
There are two ports high pressure port and Low pressure port.
If the A/C charging connector is connected to high pressure port then System can get issues.

So charging from low pressure port is necessary.
Also mostly the Refrigerant charging unit will not fit to high pressure port due to its design.


The Low pressure A/C port is up front near where the front hinges for the body are and it must be lifted up to access it.

Service Gauge Port Valves
The high-pressure service gauge port valve is located on the receiver/drier.
The low-pressure service gauge port valve is located on compressor manifold and tube near the evaporator fitting.

While charging the A/C system get the exact pressure tested.This will let you know how much refrigerant is already there in the system.This helps you to add the required refrigerant.,
Don't overflow the system with more then required refrigerant.
This will not at all help.


This details will help.
Thanks.


Users Who Viewed This Problem Also Viewed:

How to Recharge Car's Air Conditioner

http://repairhelpcenter.blogspot.com/2011/10/how-to-recharge-cars-air-conditioner.html

How to test AUTO AC pressure?


AUTO Air Conditioning Troubleshooting?

http://technoanswers.blogspot.com/2011/10/auto-air-conditioning-troubleshooting.html

Fixing refrigerant leak?


How to locate Car AC Refrigerant leak?


CAR AC INTERMITTENT COOLING?


What causes INTERMITTENT COOLING on Car AC system?


Car AC making Noise?

http://technoanswers.blogspot.com/2011/10/car-ac-making-noise.html



Friday, July 6, 2012

Vehicle Starts,Runs and Loses Power

Starts runs loses power dies won't start wait and same repeats.

2002 Dodge Cargo Van will start fine,then runs for few minutes and it will die.After waiting for few minutes it will again start and run fine but same issue repeats.

FROM WHERE TO START TROUBLESHOOTING IN THIS CASE?

In most of such cases the check engine light will come up on dash and remain steady.If in this case you notice steady check engine light on dash.Then start by getting the error code scanned.The check engine light blinking or steady on dash indicates error stored in vehicles system.Scanning will let you know what error is stored.So you can start troubleshooting by what the error code is retrieved.

THERE IS NO CHECK ENGINE LIGHT BLINKING OR STEADY?

Yes the check engine light comes but only for second while starting the ignition,then goes off.That's it:

In that case there is no error code stored.In that case the most possible cause for this start,run and die issue is 
weak heater on the upstream oxygen sensor.

WHY OXYGEN SENSOR WILL CAUSE THIS PROBLEM?

  • To Know this First Understand the working of System:

The working is as follows:-----

The sensor has a built in heater.Why it has heater, because the exhaust doesn't heat the sensor enough to properly monitor oxygen content, and the heater helps it get into closed loop operation quicker from a cold start. 

The sensor has a 5v pullup voltage on it for circuit diagnostics. This is loop mode.When the key is first turned on the sensor reading will be at 5v which means its in Lop mode.As the heater starts to work it bleeds off this voltage until the voltage is in the normal operating range. And here it enters to closed loop mode.In your case the heater is taking more then required time to get the vehicle out from loop mode to closed loop mode.This is because its weak heater.The Heater built into oxygen sensor and So the vehicle starts,then runs but dies,because vehicle is not getting to closed loop mode on time.

CAN YOU GIVE ME MORE DETAILED EXPLANATION?

Yes sure.This are all technicians details which another garage auto mechanic will easily understand.But i will make you understand in more simpler way.

Vehicle is stand still overnight.You get ready and step out of your house in the morning.
Now in this state ..........
When you enter the car and start your engine it's in open loop mode. 
WHAT is open Lop mode?
This means that the oxygen sensors are ignored and fuel control is managed basically by software alone.
But once the oxygen sensor warms up by in-built heater for a few minutes.Now the engine will go into closed loop.Now in closed  the oxygen sensor readings are then used. 
If you have a weak heater on your upstream oxygen sensor the pullup voltage will be bleeding off too slowly, and when it hits closed loop the sensor is still reading the higher pullup voltage instead of the actual sensor reading. The engine controller sees this and thinks its running rich and leans it out, giving you rough running, hesitation, and often some lean backfiring in the intake. And at last vehicle quits and dies.
As per the symptoms of your vehicles problem it seems that upstream oxygen sensor is faulty.

OK,GOOD and EASY UNDERSTANDING EXPLANATION

BUT WHAT IF I WARM THE ENGINE  FEW MINUTES BEFORE DRIVING?

In any case the Upstream Oxygen sensor has to be replaced.
Also if it's already warm and you park it and let it idle for a few minutes the sensor will cool back off. The longer it sits and idles it may run worse and worse.
In most of such problem cases  you can hear the idle air control motor opening farther and farther to keep the engine running, giving a large sucking sound under the hood. The same goes for if you start it and let it warm up before driving, it will go into closed loop while it's still idling and the sensor hasn't warmed yet.It all works on timing.The Sensor should get warmed up till particular level and in particular time.If its taking more time the engine computer will not get its indication and computer will stop operating the remaining parts.And you notice hesitation,stalling and engine quit and dies problems.

IF OXYGEN SENSOR IS FAULTY THEN WHY CHECK ENGINE LIGHT IS NOT COMING ON?

Its not faulty oxygen sensor.Its weak heater in the oxygen sensor.The sensor is good but heater is weak.The heater alone cannot be replaced.Its an inbuilt heater in the sensor.So your only option  is to replace oxygen sensor this comes with new in built heater.
You would think this problem would set a code, Yes i agree with you if the oxygen sensor is faulty then system will set the code and illuminate warning light on dash.But the software used in these engine controllers let this slip by without setting a code normally, because the voltage is still within normal operating range (not shorted to ground or an open circuit).

OK,GOT IT.BUT WHICH OXYGEN SENSOR TO REPLACE?

Yes there are more then one oxygen sensor on this vehicle.You don't have to replace all of them.
I'd recommend replacing the upstream oxygen sensor, the one in front of the catalytic converter. 
After the sensor is replaced, disconnect the battery to clear the stored fuel control adaptives out that have been falsely learned by the bad sensor.This will not cause same problem with new sensor.
If possible buy branded and original parts.They give accurate performance and last long.
Aftermarket parts are not bad parts,buy they are cheapo material parts with weak materials and they don't give exact performance in many cases.


This details will help.
Thanks.

Users Who Viewed This Problem Also Viewed:

Car loses power while acceleration?


Testing Ford Focus Heated Oxygen Sensor?

http://fordrepairhelp.blogspot.in/2012/03/testing-ford-focus-heated-oxygen-sensor.html

Now Voltage at O2 sensor on 1996 Toyota Land Cruiser?

http://repairhelpcenter.blogspot.com/2012/01/now-voltage-at-o2-sensor-on-1996-toyota.html

O2 sensor location for ford freestar?

http://technoanswers.blogspot.in/2012/02/o2-sensor-location-for-ford-freestar.html

HO2S and Catalyst Monitor Sensors working procedure?

http://technoanswers.blogspot.in/2012/02/ho2s-and-catalyst-monitor-sensors.html

1995 Oldsmobile Eighty Eight has bad O2 Sensor?

http://schematicsdiagram.blogspot.com/2011/12/1995-oldsmobile-eighty-eight-has-bad-o2.html

Replacing O2 Sensor For OBD Code P0420?

http://schematicsdiagram.blogspot.in/2012/04/replacing-o2-sensor-for-obd-code-p0420.html

Ford Focus Heated Oxygen (HO2S) Sensor?

http://fordrepairhelp.blogspot.in/2012/03/ford-focus-heated-oxygen-ho2s-sensor.html

For All types of Car models and brands help 
Go to Newly Launched

FREE Car repair guide? 
http://technoanswers.blogspot.in/2012/03/car-repair-guide.html 

& 
Complete Car repair Help FREE? 
http://repairhelpcenter.blogspot.in/2012/03/complete-car-repair-help.html


Gear indicator Shows "3" Instead Of "D"?

2006 Jeep Commander has Driving issues with Gear Shift Indicator Shows its in 3rd gear when its in Drive mode.
It will go to third gear and not other gears.

WHY GEAR INDICATOR SHOWS 3 AND WHY GEAR SHIFT ISSUES?

Its common issue.The vehicle is going in Limp mode.

In your case also the transmission is going and stuck up in Limp mode.
The problem is related to transmission and gear Shift solenoid issue.But there are many possibilities in that which can cause these problems.

The first step in diagnosing the problem will be to see what fault codes have stored.
Do you have a code reader or scan tool to check for fault codes?
Also not to worry if you dont have Scan tool.
Most parts stores like Autozone will read codes for free.

Once the codes are retrieved you can start your further troubleshooting as per Error codes.

THE ERROR CODES RETRIEVED ARE P0750 and P0700?


As i already told before that problem will be mostly related to Transmission or Solenoid pack.The Error code is indicating the same.

PLEASE GIVE ME MORE DETAILS ABOUT THIS BOTH OBD ERROR CODES?


In your jeep vehicle there is a Transmission Controlling module.Whenever there is a Error stored in the TCM( Trans control module.The Error code P0700 gets stored in the ECM( Engine control module).
This one is nothing to worry about and is just informational.
P0700 error code just tells you that there are some more error code stored in your TCM.In your case the other code is P0750.
These code is the one related to your actual problem.

P0750 is for the low/reverse solenoid in the solenoid pack inside the trans. This code sets when the voltage on the circuit is incorrect for a given state.

OK,WHAT ARE POSSIBILITIES THAT CAN CAUSE THIS INCORRECT VOLTAGE ISSUE?

There are few possibilities causing this.A  testing is required to confirm what is the actual cause.

  • The issue of  open circuit, short to power or ground on the low/reverse solenoid driver wire anywhere between the powertrain control module(PCM) and the trans.
  • Or a faulty powertrain control module(PCM) itself. A wiring problem or the module are certainly possible but not common.
  • It can be the connection issue at the large connector on the left side of the transmission, but again that's not common.Its noticed on some rare cases.Buy why to ignore that possibility too.

WHAT IS MOST COMMON CAUSE?

As per my experience and the cases which come at our garage center.In such cases the most possible problem is issue with solenoid pack.

In your case also,as per your problem description an your mentioned error code it seems like issue with solenoid.
By far the most common cause of a solenoid code is a failed solenoid, requiring solenoid pack replacement. 

WHERE IS SOLENOID PACK LOCATED ON JEEP COMMANDER?

On your model year jeep vehicle the solenoid pack is mounted to the top of the valve body in the transmission. The best thing to do if the problem is intermittent would be to do a visual inspection of the wiring, and if it's ok then replace the solenoid pack. It's not uncommon for a bad solenoid to set a fault code intermittently as the resistance of it's windings changes. 

OK,WHERE CAN I VIEW THE WIRING?

Before directly replacing the parts,its good to inspect the wiring.It can be loose or worn out/dirty or melted wiring.In that case rewiring the parts helps.
To take a look at the wiring slide underneath on the left side.Do it carefully in proper day time light if possible. Now on the left side of the trans near the front you'll see a very large black electrical connector that plugs in from the top down. This is the main connector and wiring that you have inspect and view. Make sure the wiring is visibly ok, also unplug the connector and have a look at the terminals this will give you full idea that wiring is either faulty or its proper.

HOW TO REPLACE SOLENOID PACK?
  • IS IT EASY TASK...CAN I DO IT MYSELF?
Its not very hard.But all depends upon your capability and your ability to do this task.If you have already done such parts replacement before then yes you can.But if as a newbie if you start this part replacing procedure then it will be naturally tough.Also it depends on what you have for tools and your comfort and ability level. 


For your information:----
To Replace the solenoid pack you need to drop the trans pan and drain the tranny  fluid.Also both filters need to be removed, and then dropping the valve body. 

If you are comfortable,i will mentioned the further procedure.From that you can decide whether to go into doing it yourself or getting it done by the mechanic.

Now once the valve body is out then the Torx screws that hold the solenoid pack to the valve body are removed and the pack is removed from the valve body. 

Approx time limit to complete this replacement is 2.0 hours of labor. If you are comfortable with an intermediate skill level repair and are willing to go into the trans then you can probably do it yourself. 
AS far as valve bodies go it's not a bad one to remove.

OK,CAN I DRIVE IT LIKE THAT FOR FEW MILES?

Yes its not the issue to drive in same condition for few miles or till you get it to your nearest mechanic.
In same condition driving it isn't going to hurt anything, but when it acts up you are only going to have third or third and fourth gear. You'll notice that it takes off sluggish accordingly and your cruising RPM's will be higher than normal.
But please get it repaired before you actually go for long drives or driving at highway speeds .Driving in that condition is not safe with this problem because you would have to limit your speed to keep engine RPM's down, if you drove normal highway speeds in third gear RPM's would be pretty high.And this can increase the problem.

Hope all goes well. Wish you best Luck.

This details will help.
Thanks.


Users Who Viewed This Problem Also Viewed:

1998 Toyota Camry: Gear Shift Illumination bulb is out?

http://technoanswers.blogspot.in/2012/04/1998-toyota-camry-gear-shift.html

2009 Lexus ES350: Shifter illumination bulb not Working?

http://technoanswers.blogspot.in/2012/04/2009-lexus-es350-shifter-illumination.html






For All types of Car models and brands help 
Go to Newly Launched

FREE Car repair guide? 
http://technoanswers.blogspot.in/2012/03/car-repair-guide.html 

& 
Complete Car repair Help FREE? 
http://repairhelpcenter.blogspot.in/2012/03/complete-car-repair-help.html



TIRE PRESSURE LIGHT COMING ON?

On Dash Warning light comes up on Chrysler vehicle.
The Warning light indicating issue with Tire Pressure.

FROM WHERE TO START IN THIS CASE?

As the warning light is clearly indicating problem with tire pressure.So first start by getting the tire pressure checked.It can be tested by tool.
The tire pressure testing tool is easily available at local auto parts store.Also i suggest get it checked at local auto parts store.They should test the pressure for free.

If any of the tire shows low pressure then that is where the problem lies.Get the pressure corrected and that particular tires sensor checked inspected.

BUT WHAT IF ALL TIRE PRESSURE CHECKED OK?


The tire pressure light is called the tire pressure monitoring system warning light. It obviously comes on when a tire is low, but in some cases it also comes on any time when there is a failure of any other component in the system. If you get it confirmed that all your tire pressures are ok and accurate, so there is a failure of something somewhere in the system.

HOW TO CONFIRM WHAT ELSE IS THE PROBLEM?

To confirm the exact problem a scan tool will need to be used to see what fault codes have set and go from there. Possible causes would be the pressure sensors, trigger modules that they report to, wiring, or the module that the trigger modules report to.

WHAT ARE THE MOST POSSIBLE PROBLEMS IN SUCH CASES?

Nothing can be accurately told without correct Error code retrieved by scan test.
But Still in such cases the most likely problem is one or more of your pressure sensors will need to be replaced. The sensors have internal batteries that drain over time and all tire pressure sensors will need to be replaced at some point in the vehicle's life. Your car is at the age where sensors will start to need to be replaced just from natural aging.
You can say these are problems which occur by parts age.
Every car part has some life.When it gets to the end of life,the parts stops performing as required.They don't fail completely but show the indication of failure. This where you have to inspect the sensors and confirm.If the voltage shows less and sensor is very old then replacing it is advisable.
Getting the parts inspected by the professional mechanic is very much advisable.


This details will help.
Thanks.


Tires Make Knock Rattling Noise Over Bumps?

http://whatisbyme.blogspot.in/2012/05/1998-toyota-camry-tires-make-knock.html


Spare Tire Bolts specs?

http://whatisbyme.blogspot.in/2012/05/2000-toyota-tundra-spare-tire-bolts.html


Z-Rated tire?

http://schematicsdiagram.blogspot.in/2012/04/z-rated-tire-for-1976-corvette-stingray.html


What is Best Tire For the Vehicle?

http://technoanswers.blogspot.in/2012/04/what-is-best-tire-for-vehicle.html


Do snow tires go on the back or front?

http://howtobyme.blogspot.com/2012/01/do-snow-tires-go-on-back-or-front.html


spare tire system stopped working?

http://repairhelpcenter.blogspot.com/2012/01/gmc-envoy-spare-tire-system-stopped.html


Head Lights Comes ON by Itself?

Head light problem on 2004 Chrysler Pacifica. Headlights comes ON automatically and goes OFF.

WHY THE HEADLAMPS COMES ON BY THEMSELVES?

Head lamps coming up automatically,without you actually operating it to turn ON.

There are a few possible things that can cause headlamps to come on by themselves.To confirm the issue the possibilities needs to be checked.
Possible causes would include

  • The problem with  multifunction switch on the steering column, 
  • Issue with body control module called BCM, 
  • Or issue with front control module also called FCM, and 
  • Or a shorting problem with wiring in between the components. 
WHAT CONTROLS THE HEADLAMP AND THE SWITCH?

The front control module is what controls the lamps, it controls them based on a signal from the body control module. The body control module is what actually looks at the position of the switch.

ANY OTHER POSSIBILITY FOR THIS PROBLEM?

In most of such cases the problem is mulifunction switch or its issue with any of modules if wiring is checked ok.

The components in the rest of the system are certainly possible, but are far less likely to cause the problem. Headlamps coming on by themselves is almost always caused by an internal failure of the switch. If the return voltage coming out of the switch enters the right range then the BCM will send a signal to the FCM to turn the lights on.But if the switch is got shorted then it will give incorrect signal causing the light to come ON with out command.

ANY WAY TO CONFIRM THE ISSUE?


The only way to know for sure what is going on would be to have a scan tool on it at the time it's acting up to look at the module inputs, but if you are wanting to try to repair it yourself I would recommend replacing the switch. You have a 99% chance of fixing it with a switch.Because this is what in most of such cases the problem is.And replacing the switch solves it.

Hope this details helps you out.
Thanks.



Heater fan and headlights will not turn off with ignition off?

http://technoanswers.blogspot.com/2012/01/heater-fan-and-headlights-will-not-turn.html


Only one head light works?

http://howtobyme.blogspot.com/2011/11/only-one-head-light-works-on-2001-dodge.html



Headlight Assembly Removal

http://technoanswers.blogspot.in/2012/06/headlight-assembly-removal-on-honda.html

 

Headlight Assembly Removal

http://schematicsdiagram.blogspot.in/2012/06/honda-headlight-assembly-removal.html



Headlights and Dash lights Pulsating?

http://whoisbyme.blogspot.in/2012/06/2001-chevrolet-tracker-headlights-and.html


No parking lights and headlights not turning OFF?

http://technoanswers.blogspot.com/2012/01/no-parking-lights-and-headlights-not.html

How to replace HID headlight bulbs?

http://schematicsdiagram.blogspot.com/2012/01/how-to-replace-hid-headlight-bulbs-for.html



For All types of Car models and brands help 
Go to Newly Launched

FREE Car repair guide? 
http://technoanswers.blogspot.in/2012/03/car-repair-guide.html 

& 
Complete Car repair Help FREE? 
http://repairhelpcenter.blogspot.in/2012/03/complete-car-repair-help.html





Bluetooth and Uconnect Not Responding?

2011 Dodge Charger Uconnect and Bluetooth buttons and functions are not responding or operating at all.

Its a new vehicle and all has suddenly stopped working.

WHAT IS THE REASON OF THE PROBLEM?

Many others too have noticed this issue.There a Chrysler update released for this problem.Its a known issue.Due to many complains about this same problem,the Chrysler has released the software update to clear this issue.This is a known issue on the 2011's and it is caused by a flaw in the Hands Free Module software.

Go to your dealer and get the update software run on your vehicle to get the Bluetooth and Uconnet phone functions working like before.


IS THERE ANY TEMPORARY RESET TO MAKE IT WORK?

No there is no such temporary reset to make it work.Its a known issue due to actual software problem and to clear the problem new updated software is released by company and dealer should do it for free.But yes in some cases its seen that even after Running the the new software in the vehicles system the Bluetooth and uconnect system does not respond.In that case there is simple system reset,that if the system has "locked up", you should be able to reset it by disconnecting both battery cables and holding the 2 cable ends together for 2 minutes, and then reconnecting them to the battery.

This details will help.
Thanks.


Apple Iphone 4 Will not Connect to Uconnect Phone

http://whoisbyme.blogspot.in/2012/07/apple-iphone-4-will-not-connect-to.html

Uconnect Phone Not Available Message

http://whoisbyme.blogspot.in/2012/07/uconnect-phone-not-available-message.html


For All types of Car models and brands help 
Go to Newly Launched

FREE Car repair guide? 
http://technoanswers.blogspot.in/2012/03/car-repair-guide.html 

& 
Complete Car repair Help FREE? 
http://repairhelpcenter.blogspot.in/2012/03/complete-car-repair-help.html