tag:blogger.com,1999:blog-7987059032990278152024-03-12T19:00:49.665-07:00who isHemant somaiyahttp://www.blogger.com/profile/18016566271529857503noreply@blogger.comBlogger221125tag:blogger.com,1999:blog-798705903299027815.post-65643411249224613912012-10-13T09:04:00.000-07:002012-10-13T09:04:28.439-07:00Ford Dual AC no cooling on Right side
Dual Ac cooling problem.
When on cool mode the AC only cools on left side but when heat is selected the Vehicle gets heat on both side.So heater mode is functioning but cooling mode is not running right.
On most of such cases the problem described is caused by a failed blend door actuator on 2008 ford vehicle there are two blend door actuator, one for the right side and one for theHemant somaiyahttp://www.blogger.com/profile/18016566271529857503noreply@blogger.com0tag:blogger.com,1999:blog-798705903299027815.post-29130659795345684792012-10-13T08:54:00.000-07:002012-10-13T08:54:57.434-07:00Traction control switch will not engage on 4WD High or Low
Control traction switch does not engage in 4h or 4L
On these types of cases the problems mostly noticed are transmission or rear differential also has a slight whine
But its not a issue to worry about the whine noise if its minor.
The slight whine is a common concern. This means the rear axle needs to be rebuilt with new gears and bearings. The cause is the pinion bearing Hemant somaiyahttp://www.blogger.com/profile/18016566271529857503noreply@blogger.com0tag:blogger.com,1999:blog-798705903299027815.post-85925919478713346592012-10-13T07:00:00.002-07:002012-10-13T07:00:58.883-07:00Ford focus dashboard light will not turn on
The vehicle starts fine but the dashboard lights will not turn ON.
These types of problems are noticed on many vehicle brands.
On these particular case the customer noticed issue on his 2002 ford focus.The dashboard lights were not coming ON.
On such cases the problem is either faulty dimmer switch or its issue with faulty headlight switch or its faulty /short wiring or its blown fuse in Hemant somaiyahttp://www.blogger.com/profile/18016566271529857503noreply@blogger.com0tag:blogger.com,1999:blog-798705903299027815.post-41852059253834358802012-10-09T09:46:00.001-07:002012-10-09T09:46:25.137-07:00Repair rear brakes
Problem with Brakes
There are many types of brake issues noticed.
To solve these brake related issues,follow the brake repair troubleshooting procedures.
The help links are as follows:----
Vibrations while braking On Chevrolet Van?
http://technoanswers.blogspot.in/2012/04/vibrations-while-braking-on-chevrolet.html
Dragging brakes?
http://howtobyme.blogspot.in/2012/03/Hemant somaiyahttp://www.blogger.com/profile/18016566271529857503noreply@blogger.com0tag:blogger.com,1999:blog-798705903299027815.post-51013831996418658152012-10-09T09:31:00.001-07:002012-10-09T09:31:50.222-07:002000 ford ranger Rear Brake Issues
Rear brake getting tight
Replacing read brake gets difficult.It gets stuck up hard,very difficult to loosen it.
View below diagram for rear brakes on 2000 ford ranger
First of all the rear of vehicle needs to be jacked up. take rear wheels off, be sure about the vehicle support.
Take a look behind the drum towards the bottom ,you will see a hole with wheel, has teeth on the wheel.
TakeHemant somaiyahttp://www.blogger.com/profile/18016566271529857503noreply@blogger.com0tag:blogger.com,1999:blog-798705903299027815.post-24679441180854470852012-07-21T15:01:00.000-07:002012-07-21T15:01:12.303-07:00NO voltage on Trailer Sockets?VEHICLE: 2008 Volkswagen Passat Estate.
Engine Model: 2.0 TDI 140.
PROBLEM: No voltage on Trailer wiring sockets on rear side of car.Its a 7 Pin socket trailer.
TROUBLESHOOTING SOLUTION:--
Noticed such cases at out garage few times.
On one of such case the customer noticed the problem after his tow bar electric installed in the vehicle.
On that same case the problem was blown out &Hemant somaiyahttp://www.blogger.com/profile/18016566271529857503noreply@blogger.com0tag:blogger.com,1999:blog-798705903299027815.post-85820171263974659192012-07-21T14:38:00.000-07:002012-07-21T14:38:14.153-07:00Immobilizer BypassVEHICLE: Volkswagen Golf 2000 year model.
PROBLEM: Lost both the keys.And now no way to start the vehicle without new key.
QUESTIONS: Can i by-pass the immobilizer to make the car start with normal key.
TROUBLESHOOTING DETAILS AND POSSIBLE OPTION/SOLUTION:-----
The immobilizer cannot be bypassed on your vehicle.Its not possible.The immobiliser is part of the instrument cluster.
to make theHemant somaiyahttp://www.blogger.com/profile/18016566271529857503noreply@blogger.com0tag:blogger.com,1999:blog-798705903299027815.post-86786586396126066062012-07-21T14:14:00.000-07:002012-07-21T14:14:42.936-07:00Rear Door will not openVEHICLE: Volkswagen Passat 2008 Year model.
PROBLEM:
Rear door will not open from outside.
Also If its faulty part,then what needs to be replaced and how?
TROUBLESHOOTING SOLUTION:---
First of all there are no adjustments on the rear door handle that can be done.
Its working is simple, the handle hooks into the door plate.The door Plate sits behind the rear door skin.Now Hemant somaiyahttp://www.blogger.com/profile/18016566271529857503noreply@blogger.com0tag:blogger.com,1999:blog-798705903299027815.post-13634236478667630472012-07-21T13:51:00.000-07:002012-07-21T13:51:40.858-07:00Cigarette lighter, Remote central locking, and Radio stopped working
VEHICLE: Volkswagen Polo 1998 year model.
PROBLEM: Cigarette lighter, Remote central locking, and Radio stopped working.
TROUBLESHOOTING SOLUTION:---
As all the three electrical operating functions are stopped working together.The first and the most common thing to be inspected is fuse.The fuse is shorted in your case.
There are two fuses that you need to check Hemant somaiyahttp://www.blogger.com/profile/18016566271529857503noreply@blogger.com0tag:blogger.com,1999:blog-798705903299027815.post-57197480062051892042012-07-19T14:48:00.000-07:002012-07-19T14:48:20.324-07:00White smoke and Acrid smell2007 Volkswagen touran 1.9L Engine.
PROBLEM:---
1.Noticed White Smoke while starting the Vehicle.
Smoke was noticed coming from the Front Grill.
2.And Acrid Smell Noticed just above the radiator on the right facing front of the car under the hood.
Both issues are described below:---
WHITE SMOKE ISSUE:----
These is common issue noticed by others too.Its Coolant related.
Hemant somaiyahttp://www.blogger.com/profile/18016566271529857503noreply@blogger.com0tag:blogger.com,1999:blog-798705903299027815.post-80270830393765616732012-07-19T14:06:00.000-07:002012-07-19T14:06:19.596-07:00Pin that holds the flick key part to the key fob?
The Pin is missing.
Its the Pin that holds the wriststrap to the watch.
A very little metal bar that connects the bluemotion remote inside key to the metal keyring loop.
Common issues.
There are two parts that many a times cause problems.
I will describe both.
First:
First of all you can't buy that bar .It is part of the key remote, it quite a common issue Hemant somaiyahttp://www.blogger.com/profile/18016566271529857503noreply@blogger.com0tag:blogger.com,1999:blog-798705903299027815.post-36564407978255764742012-07-15T12:43:00.000-07:002012-07-15T12:43:29.012-07:00Battery Light and ABS Light on DashBoth Battery And ABS Warning Light ON dashboard panel.
In most of such cases i have seen,the ABS light comes on because battery warning light is ON.
But if only ABS light is on then its case of codes stored in ABS module.It has to be scanned to retrieve error codes.
But in these case too both lights are ON.So i suggest first get the battery light issue solved and see,if ABS lights gets OFF,Hemant somaiyahttp://www.blogger.com/profile/18016566271529857503noreply@blogger.com1tag:blogger.com,1999:blog-798705903299027815.post-4537768343829995552012-07-14T14:34:00.000-07:002012-07-14T14:34:48.555-07:00AUDI V8 TRANSMISSION FLUID1990 Audi V8 Transmission Fluid related Issues.
HOW MUCH TRANS FLUID IS REQUIRED?
WHICH TRANS FLUID IS REQUIRED?
WHERE IS DIPSTICK FOR TRANSMISSION?
WHAT TO DO IF WRONG FLUID FILLED?
All basic issues are answered below.
It takes Approx 4 Quarts of Transmission fluid.
The Audi trans fluid is full synthetic.
The additives in the synthetic fluid are necessary for correct power Hemant somaiyahttp://www.blogger.com/profile/18016566271529857503noreply@blogger.com0tag:blogger.com,1999:blog-798705903299027815.post-2195886792872182122012-07-14T14:15:00.000-07:002012-07-14T14:15:25.920-07:00HOW TO RESET OIL CHANGE INDICATOR?2010 Dodge Dakota Oil change Indicator Reset Procedure
If the oil is already changed and you have driven few miles say 100 or more and still the oil change indicator lights is not turning off then try this reset procedure.
The Procedure stated/mentioned in the Service manual.
To reset the oil change indicator system (after performing the scheduled maintenance) perform the following procedure:Hemant somaiyahttp://www.blogger.com/profile/18016566271529857503noreply@blogger.com0tag:blogger.com,1999:blog-798705903299027815.post-91782482491262615642012-07-14T14:04:00.000-07:002012-07-14T14:04:08.849-07:00Brake Fade Issue?Brake going towards floor and not returning back to its actual position.
In this problem first check brake fluid is it low or is it leaking.Get the vacuum test done.If there is vacuum lean on brake line then it has to be solved.
Also inspect brake pads and rotors.
Dont forget to bleed the system.
Then check.
WHAT IF STILL THE PROBLEM LIES?
Mechanics call this condition as "BRAKE Hemant somaiyahttp://www.blogger.com/profile/18016566271529857503noreply@blogger.com0tag:blogger.com,1999:blog-798705903299027815.post-63934933187596769452012-07-14T13:50:00.000-07:002012-07-14T13:50:17.151-07:00Chevy Nova Seat belt Interlock OverrideWhere is Seat belt interlock override button located.
1974 Chevy nova has starting issue, no power to the trigger wire on the starter.
For seat belt override switch location,Above the master cylinder on the firewall their is a push button switch. It says start on it.
The part is called a seatbelt interlock override. Congress enacted and repealed the law in 1974 making seatbelt interlocks Hemant somaiyahttp://www.blogger.com/profile/18016566271529857503noreply@blogger.com0tag:blogger.com,1999:blog-798705903299027815.post-64212303049507109082012-07-14T13:28:00.000-07:002012-07-14T13:28:00.259-07:001996 Pontiac Grand AM: Low A/c Service valve?Low A/c pressure port.These is the port from where A/c refrigerant has to be charged.
The low side service port is located near the back of the A/C compressor.
For its easy access follow the larger line away from the compressor and it is about 4 inches down the pipe.
You have to reach down between the high pressure hose and the intake to feel it. It had a blue cap on it from the factory.
See Hemant somaiyahttp://www.blogger.com/profile/18016566271529857503noreply@blogger.com0tag:blogger.com,1999:blog-798705903299027815.post-49345081286592836392012-07-13T11:25:00.000-07:002012-07-13T11:25:25.617-07:00Cruise Control stops working,Excessive cranks to start the engine and RPM goes max 25002005 Chrysler PT Cruiser With Error codes P0325, P0340, P0032
Multiple issues noticed on Chrysler PT cruiser
Cruise control Light goes out on dash.
Hard to start,Excessive cranks to start the engine.
And RPM will not go more then 2500.
How To start Troubleshooting This Problem?
As per the OBD error codes retrieved,the problem is related to this codes.
The Error codes are Hemant somaiyahttp://www.blogger.com/profile/18016566271529857503noreply@blogger.com0tag:blogger.com,1999:blog-798705903299027815.post-48960904658596751872012-07-13T10:54:00.000-07:002012-07-13T10:54:54.288-07:00Dodge Trailer Park Lights not working?TRAILER PARK LIGHTS NOT WORKINGTrailer wiring2003 Dodge ram 2500 cab with 5.9L Diesel engine.
The Park light for dodge truck is working fine but trailer park lights not working.Trailer is factory wired.
HOW TO START TROUBLESHOOTING THIS PROBLEM?
Start with fuse,first check the fuse controlling trailer park lights.Its a 20amp fuse.If fuse is shorted,then replace the blown fuse and it will Hemant somaiyahttp://www.blogger.com/profile/18016566271529857503noreply@blogger.com0tag:blogger.com,1999:blog-798705903299027815.post-32911379923130001912012-07-08T14:22:00.000-07:002012-07-08T14:22:42.824-07:00Where is A/C Pressure Switch Located on Mercedes?2000 Mercedes Benz ML320 Low pressure Switch Location.
For Location of Low pressure switch just follow the refrigerant line from A/c compressor to the condenser.
How to replace the Low Pressure Switch?
Its very simple the old one screws out and new one screws IN.
pressure switch depresses a valve core when it screws on. It's probably safer to remove the refrigerant but if you Hemant somaiyahttp://www.blogger.com/profile/18016566271529857503noreply@blogger.com0tag:blogger.com,1999:blog-798705903299027815.post-86993219907685688482012-07-08T14:09:00.000-07:002012-07-08T14:09:33.189-07:00Where Is AC Low Pressure Port Located On Ford LCF 2006?When the AC refrigerant /Freon Level gets low the A/C system needs to be charged with refrigerant.
The A/C recharging has to be done from Low pressure port.
There are two ports high pressure port and Low pressure port.
If the A/C charging connector is connected to high pressure port then System can get issues.
So charging from low pressure port is necessary.
Also mostly the Refrigerant chargingHemant somaiyahttp://www.blogger.com/profile/18016566271529857503noreply@blogger.com0tag:blogger.com,1999:blog-798705903299027815.post-76499861021159377592012-07-06T14:59:00.000-07:002012-07-06T14:59:22.921-07:00Vehicle Starts,Runs and Loses PowerStarts runs loses power dies won't start wait and same repeats.2002 Dodge Cargo Van will start fine,then runs for few minutes and it will die.After waiting for few minutes it will again start and run fine but same issue repeats.
FROM WHERE TO START TROUBLESHOOTING IN THIS CASE?
In most of such cases the check engine light will come up on dash and remain steady.If in this case you noticeHemant somaiyahttp://www.blogger.com/profile/18016566271529857503noreply@blogger.com0tag:blogger.com,1999:blog-798705903299027815.post-54851215072128161362012-07-06T14:03:00.001-07:002012-07-06T14:04:31.833-07:00Gear indicator Shows "3" Instead Of "D"?2006 Jeep Commander has Driving issues with Gear Shift Indicator Shows its in 3rd gear when its in Drive mode.
It will go to third gear and not other gears.
WHY GEAR INDICATOR SHOWS 3 AND WHY GEAR SHIFT ISSUES?
Its common issue.The vehicle is going in Limp mode.
In your case also the transmission is going and stuck up in Limp mode.
The problem is related to transmission and gear Shift&Hemant somaiyahttp://www.blogger.com/profile/18016566271529857503noreply@blogger.com0tag:blogger.com,1999:blog-798705903299027815.post-40696203776526764662012-07-06T12:39:00.000-07:002012-07-06T12:39:22.528-07:00TIRE PRESSURE LIGHT COMING ON?On Dash Warning light comes up on Chrysler vehicle.
The Warning light indicating issue with Tire Pressure.
FROM WHERE TO START IN THIS CASE?
As the warning light is clearly indicating problem with tire pressure.So first start by getting the tire pressure checked.It can be tested by tool.
The tire pressure testing tool is easily available at local auto parts store.Also iHemant somaiyahttp://www.blogger.com/profile/18016566271529857503noreply@blogger.com0tag:blogger.com,1999:blog-798705903299027815.post-28438244206972784752012-07-06T12:21:00.000-07:002012-07-06T12:21:34.732-07:00Head Lights Comes ON by Itself?Head light problem on 2004 Chrysler Pacifica. Headlights comes ON automatically and goes OFF.
WHY THE HEADLAMPS COMES ON BY THEMSELVES?
Head lamps coming up automatically,without you actually operating it to turn ON.
There are a few possible things that can cause headlamps to come on by themselves.To confirm the issue the possibilities needs to be checked.
Possible causes would include
The Hemant somaiyahttp://www.blogger.com/profile/18016566271529857503noreply@blogger.com0